Fobik_72192ffd-6c55-41eb-9467-18d32c51bd11

Fobik Key

Programming  Instructions

Important Note: All vehicle after 2008 will have to go to dealer or locksmith for programming.


NOTE: Two programmed Completely Functional keys must be available for the following procedure to operate.
  • Obtain all keys
  • Using first programmed key turn ignition switch ON and wait 3 seconds, return to OFF position and remove key
NOTE: First and second programmed key operations MUST be performed within 15 seconds
  • Insert second programmed key and switch ignition ON
  • Wait approximately 10 seconds
  • Ensure immobilizer warning lamp begins to flash and an acoustic signal is emitted
  • Switch ignition OFF and remove key
  • Within 50 seconds, insert new key and switch ignition ON
  • Wait approximately 10 seconds
  • Ensure acoustic signal is emitted and immobilizer warning lamp remains illuminated for 3 seconds indicating programming completed
  • For each additional key repeat procedure starting from the beginning
Replacement keys can also be programmed using the diagnostic equipment
key_portion_3ef554f2-87b9-4793-96e0-6fc4d338a1da

Remote Head Key for Chrysler, Jeep & Dodge

Programming  Instructions

Key Portion Programming

NOTE: Two programmed key transmitters must be available for the following procedure to operate. If none available key transmitters can only be programmed using the diagnostic equipment.
  • Insert the first programmed key into ignition switch.
  • Switch ignition ON for at least 3 seconds but no longer than 15 seconds
  • Turn ignition OFF and remove the key
  • Within 15 seconds insert the second programmed key into ignition switch and turn ignition ON
  • After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will flash
  • Turn ignition OFF and remove the second programmed key
  • Within 60 seconds insert non-programmed key into ignition switch and turn ignition ON
  • After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will illuminate for 3 seconds
  • Switch ignition OFF, remove Key
Check operation of the programmed key transmitter. Repeat procedure for additional key transmitters if required.
Remote_portion_9959d367-7dd5-4a50-bc94-9309a6f461dc
Remote Portion Programming 
NOTE: One programmed Remote transmitters must be available for the following procedure to operate.
  • Obtain all remote transmitters.
NOTE: Any existing remote transmitters not used during programming will become inoperative.
  • Switch ignition ON.
Using a programmed remote transmitter proceed as follows.
  • Press and hold remote transmitter UNLOCK button
  • After holding the UNLOCK button for at least 4 seconds but no longer than 10 seconds, press the remote transmitters panic button for at least 1 second and release both buttons
  • Ensure acoustic signal is emitted indicating programming mode active
  • Within 30 seconds carry out the following procedure for each remote transmitter (including previously programmed remote transmitter)
  • Press any button of each remote transmitter to be programmed
  • Ensure acoustic signal is emitted after each remote transmitter operatio
  • Programming must be completed within 30 seconds
  • Switch ignition OFF or wait 32 seconds to exit programming mode
Ensure final acoustic signal is emitted. Replacement remote transmitters can also be programmed using the diagnostic equipment.
Dodge_remotes

Remote for Chrysler, Dodge & Jeep

Programming  Instructions

This programming procedure requires you to already have at least 1 working remote transmitter for your Dodge/Chrysler/Jeep. If you do not have any remote transmitters you must get this new one programmed by a qualified locksmith or dealership. Please review the procedure before attempting programming. There are 2 possible programming procedures available. Please try procedure 1 first. If that does not work, use procedure 2

Programming procedure #1
Note: Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.
  • Put key in ignition and turn ignition switch to ON position (last stop before cranking the engine)
  • Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds
  • While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. Achime should sound within three seconds to indicate the vehicle has entered programming mode
  • Press the Unlock button on the remote used in step 3. You should hear an audible tone indicating that remote has been re-programmed. This step must be done within 30 seconds of hearing the first chime in step 3
  • Within 30 seconds – Press the Unlock button on the next remote
  • Repeat Step 5 for all additional remotes including working remotes
  • Programming is now complete. Turn ignition off and test remotes to ensure proper programming
Programming procedure #2
Note: Obtain all remote transmitters for this vehicle. Sit in vehicle with all doors closed and the driver’s seatbelt on. Make sure no one else is in the vehicle.

  • Put key in ignition and turn ignition switch to ON position (as far as you can turn key without cranking engine)
  • Press and hold UNLOCK on a currently functioning remote for 4 to 10 seconds
  • While holding the UNLOCK button during the 4 to 10 second period, press the panic button for one second and release both buttons at the same time. Achime should sound within three seconds to indicate the vehicle has entered programming mode
  •  Press the LOCK and UNLOCK buttons simultaneously on the same remote used in step 3. then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed. This must be done within 30 seconds of step 3.
  • Within 30 seconds – Press the LOCK and UNLOCK button on the next remote then release. You should hear an audible tone indicating that the remote was recognized. Once tone is heard press and release the UNLOCK button on that remote. A chime should sound indicating that the remote has been programmed
  • Repeat Step 5 for all additional remotes including working remotes
  • Programming is now complete. Turn ignition off and test remotes to ensure proper programming
Tranponder_2

Transponder Key for Chrysler, Jeep & Dodge

Programming  Instructions

NOTE: Two programmed key transmitters must be available for the following procedure to operate. If none available key transmitters can only be programmed using the diagnostic equipment.
  • Insert the first programmed key into ignition switch.
  • Switch ignition ON for at least 3 seconds but no longer than 15 seconds
  • Turn ignition OFF and remove the key
  • Within 15 seconds insert the second programmed key into ignition switch and turn ignition ON
  • After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will flash
  • Turn ignition OFF and remove the second programmed key
  • Within 60 seconds insert non-programmed key into ignition switch and turn ignition ON
  • After 10 seconds an acoustic signal will be heard and immobilizer warning lamp will illuminate for 3 seconds
  • Switch ignition OFF, remove Key
Check operation of the programmed key transmitter. Repeat procedure for additional key transmitters if required.

Frequently Asked Questions

For Dodge, Chrysler & Jeep

Can I program keys myself?

Yes, you can program additional keys by yourself if you already have two working keys for your car and your car is 2008 or 2009 model. All vehicle after 2009 will have to go to dealer or locksmith for programming.

I only have one working key fob; can this be programmed any other way?

Sorry, self-programming can only be done if you have two working keys and if your car is 2008 or 2009 model. In your case, please take the new fob to any automotive locksmith near your area and they should be able to pair this key to your car.

Does this come with the programmable chip?

Yes, please try self-programming instruction or take it to local automotive locksmith for getting them programmed to your car.

Can i program this myself if I have 2 working fobs? your instructions seem contradictory on this question. dodge grand caravan 2013.

Only 2008 and 2009 models can be self-programmed all other cars do not have self-programming capability. Please take it to any automotive locksmith and they should be able to help you out.